Parabody 883 User Manual

1883 SECOND STACK OPTIONFOR 880 GYM SYSTEMCLASS HPART # 7168901REV. CRevision: 3/08/02USER’S GUIDEWARNING:Read and follow all directionsfor each step

1001234561/2 1/2 1/2 1/2 1/2 1/2STEP 9: FIGURE 9• Unscrew the threaded ends of the WEIGHT STACK CABLE from the WEIGHT STACK SHAFT and remove the

11STEP 10: FIGURE 10• Assemble two 3-1/2” PULLEYS (9) to the LEFT BOOM BRACKET (2) using two 3/8 X 1-3/4” BOLTS (13) and two 3/8”LOW HEIGHT LOCK

1201234561/2 1/2 1/2 1/2 1/2 1/2STEP 10: FIGURE 11• Route the new PRESS STACK CABLE (7) thru the PRESS STATION as shown. (NOTE: Remove pulleys f

13STEP 12: FIGURE 12• Route the new PRESS STACK CABLE (7) thru the PEC STATION as shown. (NOTE: Remove pulleys for ease of installation.)Slide G

STEP 14: FIGURE 1414• Route the LEG CABLE (8) around the 3-1/2” PULLEY on the PULLEY PLATES using one existing 3/8 X 1-3/4” BOLT and oneexisting

15TIGHTEN!20 623 3STEP 15: FIGURE 15• SECURELY tighten all loose frame connections.• Slide the SHAFT COLLARS (23) to the top of the GUIDE RODS (

16 FIGURE 1STEP 1:PRESS/LEGCABLE• NOTE: Follow these steps if assembling the SECOND STACK OPTION to a completely assembled (including cables)880

SHORT LEG PRESS CABLE FIGURE 2STEP 2:• Carefully remove and discard the SHORT LEG PRESS CABLE from the LEG PRESS as shown in FIGURE 2.17STEP 3:

18STEP 4: FIGURE 4• SECURELY assemble the STACK BASE (1) to the BASE FRAME using two 3/8 X 4” BOLTS (15), two previously removed 3/8 X4-1/4” BOLT

STEP 6: FIGURE 6SHORT LEGPRESS CABLE• Remove the rest of the SHORT LEG PRESS CABLE from the FRAME as shown in FIGURE 6. (NOTE: Remove pulleys for

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OFEQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!1. Before using, read all the warnings and

STEP 8: FIGURE 8• SECURELY assemble the PEC STATION PAD to the FRAME using two previously removed 3/8 X 3” BOLTS and two 3/8”WASHERS (18). See

21 FIGURE 10STEP 10: FIGURE 9• Insert two WEIGHT PLATE BUSHINGS (21) into each of the fifteen WEIGHT PLATES (20) as shown in FIGURE 9.STEP 9:•

FIGURE 11STEP 11:22• Insert two GUIDE RODS (3) into the STACK BASE (1) as shown on FIGURE 11. (NOTE: If the 880 SHROUD OPTION waspurchased, pl

FIGURE 12STEP 12:01234561/2 1/2 1/2 1/2 1/2 1/2• CAREFULLY remove the BOOM PLATE (10) from the the REAR UPRIGHT and the FRAME as shown in FIGURE

24STEP 14: FIGURE 14• Unscrew the threaded ends of the WEIGHT STACK CABLE from the WEIGHT STACK SHAFT and remove the two PULLEYSfrom the BOOM BRA

25STEP 15: FIGURE 15• Assemble two 3-1/2” PULLEYS (9) to the LEFT BOOM BRACKET (2) using two 3/8 X 1-3/4” BOLTS (13) and two 3/8”LOW HEIGHT LOCK

STEP 16: FIGURE 16PULLEYPLATES• Route the previously removed original LAT CABLE through the FRAME (1) and assemble one 3-1/2” PULLEY to the PULLE

2701234561/2 1/2 1/2 1/2 1/2 1/2STEP 18: FIGURE 18• Route the new PRESS STACK CABLE (7) thru the PRESS STATION as shown. (NOTE: Remove pulleys f

28STEP 19: FIGURE 19• Route the new PRESS STACK CABLE (7) thru the REAR UPRIGHT as shown. (NOTE: Remove pulleys for ease of installa-tion.) Sli

STEP 21: FIGURE 2129• Route the LONG LEG PRESS CABLE around the 3-1/2” PULLEY on the PULLEY PLATES using one existing 3/8 X 1-3/4” BOLTand one e

IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the ParaBody 880 Second Stack Option. Please read these instructio

30CABLE ROUTING DIAGRAM FIGURE 22STEP 22:• Carefully route the LONG LEG PRESS CABLE thru the LEG PRESS as shown in FIGURE 22 and assemble the LO

31TIGHTEN!20 623 3STEP 23: FIGURE 23• SECURELY tighten all loose frame connections.• Slide the SHAFT COLLARS (23) to the top of the GUIDE RODS (

PART #716020871679086523401709570170121026957302716570171561013116201697220131080026978101KEY123456789101112QTY112121112121PART #310292431028073102906

STEP 1:501234561/2 1/2 1/2 1/2 1/2 1/2• REMOVE the PRESS/LEG CABLE from the 880 GYM SYSTEM . Discard the PRESS/LEG CABLE . See FIGURE 1. (NOTE:Remov

STEP 2: FIGURE 26• Remove the two 3/8 X 4” BOLTS, four 3/8” WASHERS and two 3/8” LOCK NUTS from the REAR UPRIGHT as shown inFIGURE 2.3/8 X 4” BOL

7 FIGURE 5STEP 5: FIGURE 4• Insert two WEIGHT PLATE BUSHINGS (21) into each of the fifteen WEIGHT PLATES (20) as shown in FIGURE 4.STEP 4:• Sl

FIGURE 6STEP 6:8• Insert two GUIDE RODS (3) into the STACK BASE (1) as shown on FIGURE 6. (NOTE: If the 880 SHROUD OPTION waspurchased, place

FIGURE 7STEP 7:01234561/2 1/2 1/2 1/2 1/2 1/2• CAREFULLY remove the BOOM PLATE from the the REAR UPRIGHT and the FRAME as shown in FIGURE 7. Dis